Skip to content

Tonearm geometry: null points, overhang and a PDF protractor

Enter the pivot-to-spindle distance and pick a geometry (Baerwald, Löfgren B, Stevenson), or ask for the null points that give the least error by a criterion. The tool computes effective length, overhang and offset angle, plots the tracking error over the whole record, checks an arm that is already mounted from what you measured, and generates a PDF protractor at true size.

Geometry

The arm

mm

Measure it on your own deck and arm; we do not take it from a catalogue.

The record

mm
mm

Default 60.325 and 146.05 mm: the modulated area of a 12 inch LP (IEC).

A compromise: not the best on any measure in the table, but far from the worst.

Results

Effective length

239.31 mm

Overhang

17.31 mm

Offset angle

22.99°

Null points

66.04 / 120.90 mm

Peak error

1.80°

at radius 146.1 mm

Mean error

0.73°

Error per cm (rms)

0.08

degrees/cm

Tracking error is the angle between the cartridge axis and the groove's tangent, in degrees; the same angle does more harm toward the centre, which is why it is also shown per cm of radius.

Tracking error over the record

-20280100120140radius (mm)error (degrees)
chosen geometry0°
Comparison

The geometries side by side, for this arm

Click a row to choose it. The values are computed, not taken from a table.

GeometryNull pointsEffective lengthOverhangOffsetPeakMeanPer cm
66.04 / 120.90239.3117.3122.99°1.80°0.73°0.08
70.29 / 116.60239.7517.7522.94°2.00°0.65°0.07
60.33 / 117.42237.4215.4221.98°2.20°0.89°0.10
Your mounted arm

Check an arm that is already mounted

Measure the overhang (with a gauge) and the cartridge's offset angle; the tool computes where the error is actually zero and how far off it is.

mm
°

Fill in overhang and offset to see the diagnosis.

PDF protractor

Protractor at true size

A PDF with the spindle, the stylus arc between the grooves, the null points with a grid on the tangent and a 100 mm test square. Print at 100 %, no “fit to page”, and measure the square: if it is not 100 mm, do not use the sheet.

Paper

The ideas behind the controls

Compare the criteria
Put your arm in the table: Baerwald has a smaller peak error than Löfgren B, but Löfgren B has a smaller error per cm of radius, so it does better toward the centre of the record.
Diagnose the set-up
Enter the measured overhang and offset: if the stylus is tangent nowhere, you see it on the chart before you print anything.
Choose by what you play
If you listen a lot near the end of a side, the optimum per cm or Stevenson give smaller error in the inner grooves.

Common mistakes

  • Printing the protractor scaled: always check the 100 mm square.
  • Measuring pivot to spindle to the wrong points: it is from the pivot's centre to the platter spindle's centre.
  • Thinking a null point is “perfect”: the error is zero only at those two radii.

What this tool cannot tell you

  • The calculation is pure geometry: it does not account for skating force, arm height, azimuth or stylus shape.
  • Distortion is not converted to percent; it shows the error angle and the angle per cm of radius.
  • The preset null points are the ones known in the literature; what each one optimises I checked numerically, not from the original papers.
  • The 100 mm square checks the printer's scale, not the flatness of the paper or how it sits on the platter.

Where the formulas come from

  • Baerwald (1941); Löfgren (1938); Stevenson (1966), as usually cited — The origin of the null-point choices; authors and years are the usual ones, not re-checked by the tool in the original papers.
  • IEC 60098: dimensions of the modulated area of a record — Radii 146.05 and 60.325 mm for the 12 inch LP.

Frequently asked questions

What is a null point?

The radius on the record where the cartridge axis is exactly tangent to the groove, so the tracking error is zero. A pivoted arm has two.

Why several geometries?

With two null points you choose where to put the error: evened out over the record, smaller toward the centre, or zero exactly at one groove; each choice gives a different overhang and offset.

What is overhang?

How far the stylus reaches past the platter spindle: effective length minus pivot-to-spindle.

Tonearm geometry: null points, overhang and a PDF protractor · Strunin